Thrust Roller Control in Kiln using PLC and HMI
DOI:
https://doi.org/10.24036/05hv5c13Keywords:
Thrust Roller , Kiln , PLC, HMI, Monitoring, ControlAbstract
The thrust roller control and monitoring system is very important in the cement production process, especially in the cement processing process that occurs in the Kiln equipment. At PT. Semen Padang, the thrust roller control and monitoring process using a potentiometer sensor often experiences problems. Based on this, this study aims to develop a solution to the problem of the thrust roller control and monitoring system to make it more accurate. This study was conducted using an experimental method. With this method, the author took some test data on the ultrasonic sensor as a substitute for the potentiometer sensor and then compared the test data with the actual value to determine the level of feasibility and error in the system. The research instrument used in the test was a meter while the object of the study was the thrust roller prototype that had been made. Based on the test results, the thrust roller control and monitoring system has been successfully carried out where the thrust roller movement is displayed in the form of an HMI screen simulation with a small error rate, namely from 20 trials 18 of them were successful while the remaining two experienced errors
Downloads
References
[1] K. K. Ummatin, Q. A. M. O. Arifianti, A. Hani and Y. Annissa, "Quality Analysis of Refused-Derived Fuel as Alternative Fuels in the Cement Industry and Its Evaluation on Production," 2019 International Conference on Engineering, Science, and Industrial Applications (ICESI), Tokyo, Japan, 2019, pp. 1-6, doi: 10.1109/ICESI.2019.8863000.
[2] A. Anandevit, “Analisis Kualitas Semen Jenis Portland Composite Cement (PCC) di Pabrik Indarung V PT Semen Padang.,” 2021.
[3] C. Sonjaya, “Analisis Pompa Hydraulic Kiln Trhuster Dan Perawatan Pada Rotary Kiln Plant 10 Pt X,” in In Prosiding Seminar Teknologi Majalengka (Vol. 7, Pp. 249-253), Nov. 2023.
[4] A. Fikri, “Perhitungan Numerik Tegangan Geser Maksimum pada Shell Rotary Kiln Akibat Pembebanan Mekanik,” Doctoral dissertation, Universitas Andalas, 2021.
[5] V. Giarine, “Redesain Spring Plate Pada Rotary Kiln Dengan Menggunakan Metode Optimasi Topologi,” Tugas Akhir, Institut Teknologi Sepuluh Nopember, 2018.
[6] W. R. Hidayat and D. Suryadi, “Modal Analisis Pada Rotary Kiln Dengan Menggunakan Metode Elemen Hingga Modal Analysis in Rotary Kiln Using Finite Element Method,” vol. 6, no. 2, p. 2022.
[7] N. Glebov, T. Kruglova and M. Shoshiashvili, "Intelligent Electro-pneumatic Module for Industrial Robots," 2019 International Multi-Conference on Industrial Engineering and Modern Technologies (FarEastCon), Vladivostok, Russia, 2019, pp. 01-04, doi: 10.1109/FarEastCon.2019.8934864.
[8] M. I. P. Azahar, A. Irawan and R. M. Taufika, "Fuzzy Self-Adaptive PID for Pneumatic Piston Rod Motion Control," 2019 IEEE 10th Control and System Graduate Research Colloquium (ICSGRC), Shah Alam, Malaysia, 2019, pp. 82-87, doi: 10.1109/ICSGRC.2019.8837064.
[9] N. Niko, A. Abimanyu, and S. Safaruddin, “Evaluasi Kinerja Alat Rotary Kiln Ditinjau Dari Efisiensi Termal Dan Air Fuel Ratio (Afr) Di Pbr Ii Pt. Semen Baturaja Tbk,” PHENOMENON : Multidisciplinary Journal Of Sciences and Research, vol. 1, no. 02, pp. 90–100, Aug. 2023, doi: 10.62668/phenomenon.v1i02.774.
[10] F. Rahmadi and M. Yuhendri, “Kendali Kecepatan Motor DC Menggunakan Chopper DC Dua Kuadran Berbasis Kontroller PI,” JTEIN J. Tek. Elektro Indones., vol. 1, no. 2, p. 241, 2020, doi: https://doi.org/10.24036/jtein.v1i2.71.
[11] A. R. Suharso, G. B. Santoso, A. Hendartono, and R. B. Kumara, “Perbandingan Sensor Incremental Rotary Encoder dan Potensiometer pada Simulasi Kemudi Kapal Berbasis Arduino,” ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika, vol. 11, no. 1, p. 155, Jan. 2023, doi: 10.26760/elkomika.v11i1.155.
[12] X. -x. Luo, M. -z. Yuan and H. Wang, "Simulation of system identification and decoupling control of rotary lime kiln system," 2010 8th World Congress on Intelligent Control and Automation, Jinan, China, 2010, pp. 5814-5818, doi: 10.1109/WCICA.2010.5554599.
[13] N. Y. Putri and R. Mukhaiyar, “Control and Monitoring System Process Handling Production on SMI 4.0 Machines using PLC Controller Wirelessly Based on Human Machine Interface.,” JTEV (Jurnal Teknik Elektro dan Vokasional), vol. 8, no. 1, pp. 158–168, 2022.
[14] Y. D. Satriani and M. Yuhendri, “Kontrol Posisi Motor Servo Berbasis Human Machine Interface dan Internet of Things,” JTEIN J. Tek. Elektro Indones., vol. 4, no. 2, pp. 949–956, 2023.
[15] A. Minsandi et al., “Design and Implementation of Robot Abu Robocon Using Joystik Wireless Based on Extrasenory Percepsion,” J. Ind. Autom. Electr. Eng., vol. 01, no. 01, pp. 39–45, 2024.
[16] Y. Rahmanto, A. Rifaini, S. Samsugi, and S. Dadi Riskiono, “Sistem Monitoring Ph Air Pada Aquaponik Menggunakan Mikrokontroler Arduino Uno,” JTST, vol. 01, no. 1, pp. 23–28, 2020.
[17] R. I. Rosihan and H. A. Yuniarto, “Analisis Sistem Reliability dengan Pendekatan Reliability Block Diagram,” Jurnal Teknosains, vol. 9, no. 1, p. 57, Dec. 2019, doi: 10.22146/teknosains.36758.
